|
|
|
| |
|
|
| |
1 of 2 |
| |
|
 |
Use as a hands-free backing support when butt-welding and welding holes in sheetmetal or whenever an open area needs to be bridged with weld. Welding material will not stick to the copper plate. 1/8" solid copper with high-strength, high heat magnets. Made in USA. |
 |
Use as a hands-free backing support when butt-welding and welding holes in sheetmetal or whenever an open area needs to be bridged with weld. Welding material will not stick to the copper plate. 2"x 4" x 1/8" solid copper with high-strength, high heat magnets. Made in USA. |
|
Use as a hands-free backing support when butt-welding and welding holes in sheetmetal or whenever an open area needs to be bridged with weld. Welding material will not stick to the copper plate. 2"x 8" x 1/8" solid copper with high-strength, high heat magnets. Made in USA. |
 |
This Alumiweld System lets you repair aluminum and pot metal at home for a fraction of the cost. Even difficult to replace die-cast zinc and pot metal parts, so common on vintage cars, can be repaired and saved. Use with a pro- pane torch or a Jeweler's Torch. Rods are approx. 9" long. This unique soldering-type process requires no flux and produces a strong repair that can be filed, threaded, polished and plated. Step-by-step instructions included. Use Jigging Putty to hold broken parts in position during welding and to shield surfaces from heat damage. |
 |
Eastwood has taken its most popular welding accessories and placed them into a single kit. The kit includes four Butt Weld Clamps that accurately align and firmly hold-in-place panels edge to edge leaving a .040inch gap for full weld penetration plus our specially designed 4 and 8inch magnetic copper Welding Backers. These handy magnetic backers provide panel support for butt welding and welding holes, preventing warpage and burn-thru. |
 |
Upgrade your Eastwood Welder's Helper with these two specially designed welding backers for curves and angles. Use the Gradual Curve head for fins trunk, decks and other curved areas. Use the 90 Degree Angle head for joints and angles. Each Helper has three holes that allow you to position the head Left, Right or Straight. The Helper's act as heat sinks and support your welding from behind as you repair damaged metal panels. MADE IN USA. NO HANDLE included |
 |
A precision pulling tool for use with our stud welders and others with 1" OD grounding ring. Just seat the stud welder in the Dent Killer, bring grounding rods into surface contact and trigger your stud welding gun for .5-1 seconds to attach the reusable "stud". Raise metal with the attached 3:1 lever for exactly the right amount of pull to achieve a level surface. Nylon faced 5-1/2" long support legs adjust from 3" to 7" to span damage & styling lines. Rotate the tool to release the stud. Great for use along creases or in areas without enough overhead clearance to use a sliding hammer. Imported. |
 |
Versitile Stick Welder From Firepower - The model FP 100 stick welder from Firepower can be used for a variety of welding jobs. This light 27 lb. unit features adjustable welding output to 85 amps AC with a 15% duty cycle. Easily welds 18 gauge up to 3/16" steel. When used with the Stitch Welder (19045) this welder can handle sheet metal as thin as 22 gauge. Use the Spot Welder (19089) to duplicate spot welds. The FP 100 includes permanently installed 6' cables with attached ground clamp and stick holder, and complete instructions. Welding shield/helmet Not included. We recommend the (19012) welding helmet. |
 |
Fill Holes in Sheet Metal Without Burn-Through - The rectangular copper paddle measures 1 5/16" wide by 6 1/8" long. This flat copper plate is clamped onto the metal and then welded from the other side. Weld deposited metal will not stick to the copper while the copper absorbs heat and prevents burn through. |
 |
2.5" long copper back up pad allows you to create butt welds in thin material without the fear of burn through Magnetic base securely adheres copper pad to weld area and can be adjusted to fit. Simply attach to back side of butt weld area and begin stitch welding with your mig gun or tig welder. Unit is quickly repositioned to next weld area in seconds. |
 |
Powerful magnets keep panels, pipes or other parts securely in place during welding,soldering and assembly operations. Shape permits panels to be arranged at 45 deg.,90 deg. or 135 deg. angles. Comes with manufacturer's lifetime warranty. Dimensions are 4 1/2"L x 3 1/2" W x 1/2" D. |
 |
Take the intimidation out of MIG Welding with this instructional DVD. MIG Welding is widely used for car and motorcycle building and modification but few people really understand how each of the variables affects the finished weld. his program can be easily understood by a beginner, but it covers information even seasoned professionals can learn from. Ron Covell goes through the entire process step-by-step, and gives clear descriptions of how each factor changes the weld, including wire speed, voltage, wire stickout, gun angle, travel speed, and gas flow. 70 minutes DVD. |
Copyright 2007 OnlineToolSupply.com
|
|
